Showing results: 1816 - 1830 of 2550 items found.
-
SA831 -
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Pulsed ESR/EPR -
Insight Product Company
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
ERAVANT
Benchtop, broadband driver amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power and a superior gain flatness and low noise performance. The standard offering focuses on general purpose applications and covers the frequency range of 1 to 110 GHz. However, custom designs are also offered to meet any user’s specific needs.
-
RPT-5 -
DeltaTech Electronics
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
MISS -
BioAge s.r.l.
The Micro Smart System is one of the many autonomous systems with very low consumption designed by BioAge. The system is characterized by autonomous operation with very low energy consumption thanks to its operation in "Energy Harvesting" which allows to exploit the power supply from a micro solar panel with which each sensor is equipped. Furthermore, these systems are equipped with radio frequency communication able to remotely transmit the information acquired by the sensors on board, it is therefore possible to create a network of sensors, operating autonomously and with a very high autonomy thanks to solar energy.
-
Insight Product Company
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Insight Product Company
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Insight Product Company
They prevent failure of of input amplifying stage of low-noise receivers with radio pulse power up to 5000 Watt. They can also be applied as seperate units without power supply and acting as controlled switches. This component is very valuable for radar applications because the high power transmitter and extremely sensitive receiver work with a single antenna.
-
Insight Product Company
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
-
IPPS 2-6/60 -
Insight Product Company
Power supply/sweeper model IPPS 2-6/60 specially designed by Insight Product Company to operate sub-mm wave BWO at frequencies up to 1500 Ghz. IPPS 2-6/60 produces highly stable regulated voltages for slow wave structure (anode) and filament/heater. This power supply is designed to simplify the operation with BWO, to protect BWO against distraction during start/stop routines, to allow fast frequency sweeping in the entire band, and also to allow BWO to be used within a frequency stabilization system.
-
ATmega32U4 Board -
SparkFun Electronics
This is the LilyPad Arduino USB board, controlled by an ATmega32U4 with the Arduino bootloader. It has a built in power supply socket and an on/off switch with the only extra piece of hardware you need to program the LilyPad USB is a micro-USB cable, since the new IC has built-in USB support. Any of our LiPo batteries can be plugged right into the JST socket to provide you with easy, on-the-go power. That LiPo battery is even rechargeable through the board, no more special external LiPo chargers required!
-
Robson Technologies, Inc.
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
RS-485 -
SparkFun Electronics
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
OP-SB85L -
LINEEYE Co., Ltd.
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
AWS-0101 -
Anokiwave Inc.
The AWS-0101 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and dual beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain during transmit mode, +15 dBm output power during transmit, and 3.4 dB NF during receive. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8V supply, and is packaged in a 56 lead 7x7 QFN for easy installation in planar phased array antennas.